RADIANT METALLIC INSULATION FIBERGLASS HOSE PIPE WRAP HEAT SHIELD COLD AIR TAPE

Description

ALREADY PRICED TO MOVE, BEST OFFERS FOR 2 OR MORE
FOR ONE KIT PLEASE USE THE BUY IT NOW OPTION
FIBERGLASS LINED RADIANT METALLIC HEAT SHIELD WRAP
25 FEET!
WRAP SPECS:
MATERIAL (INNER):
PURE VIRGIN GLASS FIBER
(OUTER):
ALUMINUM SILICON ALLOY
THICKNESS:
1/16 INCH
WIDTH:
1 INCH
TEMP:
1200°F CONTINUOUS
COLOR: METALLIC
PREMIUM WEAVE STAYS TOGETHER
RADIANT HEAT PROTECTION UP TO 2000°F !
CAN BE USED IN
MULTIPLE APPLICATIONS INCLUDING:
AIR INTAKES
INTERCOOLERS
SUPERCHARGERS
TURBO PIPES
TUBING
EXHAUST HEADERS AND PIPES
STARTERS
HOSES
WIRING
COLD AIR INDUCTION SYSTEMS
PROTECT BODY PARTS AND COMPONENTS
REFLECT HEAT AWAY FROM SENSITIVE ELECTRONICS
USE TO MAKE CUSTOM BLANKETS
KEEPS HEAT WHERE YOU WANT IT AND AWAY FROM WHERE YOU DON'T!
NOT JUST FOR HIGH PERFORMANCE VEHICLES!
GREAT FOR THE EVERYDAY DRIVER TOO!
EXTENDS ENGINE LIFE
INSTANT FUEL SAVINGS, HIGHER MPG
PROVEN TO REDUCE UNDER HOOD HEAT BY 70%
EASILY INSTALLED BY THE NOVICE AND PRO ALIKE
WILL REDUCE TURBO LAG
WILL INCREASE HORSEPOWER
EXTENDS THE LIFE OF PLASTIC PARTS, HOSES, WIRING & MORE,
BY PREVENTING DRY ROT AND EARLY BREAK DOWN.
NOT ONLY FOR HEADERS, WRAP HOSES, PIPES, TUBES TURBO/SUPERCHARGER HARDWARE AND MORE
A GREAT WAY TO HIDE BLUING, WELD LINES OR JUST PLAIN UGLY PIPES ON OLDER OR CUSTOM MADE PIPES
HOW MUCH FIBERGLASS WRAP DO I NEED FOR MY PROJECT? / LOOK BELOW, OR SEND ME A PICTURE.
YIELD CHART:
CHART =
WRAP NEEDED PER 1 LINEAR FOOT OF PIPE YOU PLAN TO WRAP.
ALWAYS ADD 10% TO TOTAL JOB AND ANOTHER 8-14" PER BEND APPROX. DEPENDING ON THE ANGLE
PIPE
DIAMETER
INCH/mm
1” WIDE WRAP
PER LINEAR FOOT
Inches”/feet’
2” WIDE WRAP
PER LINEAR FOOT
Inches”/feet’
1-3/8”/35mm
70”/5’
30”/2.5’
1/1/2”/38mm
76”/6.33’
33”/2.75’
1-5/8”/41mm
82”/6.8’
35”/2.9’
1-3/4”/45mm
88”/7.33’
38”/3.16’
1-7/8”/48mm
95”/7.9’
41”/3.5’
2”/50mm
101”/8.4’
44”/3.66'
2-1/8”/53mm
108”/9’
46”/3.83’
2-1/4”/57mm
113”/9.4’
49”/4’
2-1/2”/64
125”/10.5’
52”/4.33’
3”/76mm
136”/11.33’
60”/5’
EXAMPLE:
IF YOU HAVE 2" PIPES THAT ARE 10' LONG AND YOU WANT TO USE A 2" WIDE WRAP.....
LOOK AT THE CHART, FIND YOUR PIPE SIZE ON THE LEFT (IN THIS CASE 2" OR 50MM {SAME THING} ) THEN FOLLOW THE CHART TO THE RIGHT UNDER "2" WIDE WRAP" YOU WILL SEE YOU NEED 44 INCHES OR 3.83 FEET
PER LINEAR FOOT OF PIPE
TAKE 44" or 3.66' AND MULTIPLY BY 10FT = 440 INCHES/36.6 FEET THEN ADD 10% ..... SO YOU NEED A 50 FT ROLL. DON'T FORGET TO ADD FOR BENDS
INSTALLATION:
CAN BE INSTALLED EITHER:
METALLIC SIDE DOWN, BEST FOR KEEPING HEAT IN.
OR, METALLIC SIDE UP FOR A RADIANT BARRIER KEEPING HEAT OUT.
WEAR GLOVES AND A LONG SLEEVE SHIRT TO PREVENT ITCHING/AND IRRITATION.
WRAP WILL SMOKE LIGHTLY AFTER INITIAL INSTALLATION (JUST FEW MINUTES).
STARTING AT THE FLANGE END LEAVE ABOUT ¼"- ½" FOR HARDWARE.
EACH WRAP SHOULD OVERLAP THE PREVIOUS LAYER BY APPROXIMATELY ¼"- ½"
TURNS AND CURVES WILL HAVE BIT MORE OF AN OVERLAP.
TRY TO KEEP THE WRAP AS SNUG AS POSSIBLE AS YOU GO AND CONTINUE TO THE END OF THE PIPE.
USE A STAINLESS STEEL TIE AT ENDS TO HOLD WRAP IN PLACE.
YOU'RE DONE!
IF YOU NEED STAINLESS STEEL TIES. PLEASE LOOK IN OUR STORE (SEE LINK BELOW)
CHECK OUT OUR OTHER FIBERGLASS, LAVA AND CERAMIC WRAP COMBINATIONS, KITS AND ROLLS. WE ALSO HAVE STAINLESS TIES IN 3/16" (STANDARD) AND 5/16 (MONSTER) IN LENGTHS FROM 4"- 54"! AND PACKS FROM 5 - 1000